AddOn 10/100/1000Base-TX to 1000Base-LX SMF 1310nm 10km PoE Media Converter
Converts copper Ethernet to single-mode fibre at 1310 nm over 10 km while delivering 48 V PoE power to remote devices
- Extends network reach up to 10 km via single-mode fiber
- Powers remote devices with 48 V PoE over copper up to 100 m
- Converts copper RJ-45 to fiber LC at gigabit speeds
- Open SFP slot allows SX, LX or BX transceiver choice
- Link Fault Pass-through monitors both fiber and copper for signal loss
Copper-to-fibre PoE bridge
This media converter links a 10/100/1000Base-TX RJ-45 port to a 1000Base-LX LC fibre interface at 1310 nm. It also supplies 48 V power over the copper pair to an IEEE 802.3 af powered device up to 100 metres or 330 feet away. The open SFP slot lets you swap SX, LX or BX modules for different reach or wavelength needs. It is built for installers who need gigabit fibre reach plus remote device power in one box.
Replaces copper-only runs past 100 m
Standard twisted-pair links stop at 100 metres; this unit pushes gigabit traffic 10 km over single-mode fibre while still feeding a PoE device. The jump is worth it when cameras, access points or IoT sensors sit beyond copper reach but AC power is unavailable at the far end. It also upgrades existing multi-mode fibre plant to single-mode without changing the powered device.
10 km single-mode headroom, 100 m PoE limit
The fibre side comfortably handles campus-building spans up to 10 km at 1 Gbit/s. Headroom ends at the 100 metre PoE copper leg; devices farther than that need a mid-span injector or local power. The converter does not route or switch — it only extends and powers — so VLANs, QoS or redundancy must be handled upstream.
How it compares
Measured against everything we stock in SFP & SFP+ Transceiver Modules, at today’s prices. Recalculated every night.
- Price $149.99
- Typical for this category: the median of 1,470 items is $138.49.
New to this? Buying networking gear with crypto — what to check, what it costs to pay, and what is never asked for.
Specifications
No published specifications for this item yet.
Questions about this item
Does the AddOn PoE media converter mount in a rack or sit on a desk?
The unit is a standalone desktop device with no rack ears or DIN-rail clips mentioned, so it sits on a flat surface or shelf.
What is the correct order to connect fibre, copper and power so the LFP function works?
Insert the LC single-mode fibre first, then the RJ-45 copper link, and finally apply AC/DC power; powering up before both links are live can prevent Link Fault Pass-through from detecting the correct signal state.
Which parts will need replacement after extended use?
The SFP transceiver in the open port can be swapped for SX, LX or BX modules, and the internal PSE controller or power supply may require service after long-term PoE loading.
More in SFP & SFP+ Transceiver Modules
Similar items
Finisar Corporation FTLX1475D3BCV 10GBase-LR 1000Base-LX Dual Rate 10 km 1310 nm SFP transceiver
HPE JD089B Gigabit Ethernet SFP Transceiver 1000Base-T RJ-45
- Transceiver
- HCRP, SPP
Perle 05050204 SFP transceiver 10/100Base-TX 100Base-FX 1.24 Mile
- 1 x RJ-45 Network,…
- 1.24 Mile
STARTECH MASFP10GBLR SFP+ transceiver 10GBASE-LR 10km 1310nm LC
- Transceiver
- IEEE 802.3ae 10 Gbi…
Tripp Lite N785-001-LC-MM 10/100/1000 LC Duplex 850nm 550m Media Converter
- Side A - Connector…
- Converter





