Wilfly ATX 3.1 12+4Pin 90° Reverse to 2×8Pin GPU Extension Cable 10cm
Converts two 8-pin PCIe cables into a single 12+4-pin 90-degree reverse connector for RTX 5090 graphics cards using 16 AWG sleeved wiring
- First connector12+4Pin Male 90 Degree Reverse
- Second connector2 × 8Pin Male
- Connector count3
- Product colorBlack
- Overall length10CM
- Converts dual 8-pin to 12+4-pin without replacing the PSU
- 90-degree reverse connector eases routing in tight cases
- 10 cm sleeved extension keeps cable runs tidy
- 16 AWG wires rated for 800 W and above power supplies
- PCIe 5.0 design supports 32 GT/s data link speeds
Power conversion for RTX 5090 builds
This 10 cm cable converts two eight-pin PCIe outputs into a single 12+4 pin ATX 3.1 connector. It lets an existing 800 W or higher power supply drive an RTX 5090 or newer 6000-series card without replacing the unit. The 90-degree reverse plug keeps the cable close to the card edge.
Headroom at 16 AWG with dual eight-pin feeds
Two eight-pin connections share the load, so the 16 AWG conductors stay within spec for 5090-class draw. The design avoids daisy-chain splits that can concentrate current on one wire. Peak demand above the PSU rating will still trip protection, so total system power must remain inside the supply limit.
Sleeved construction and 90-degree reverse mounting
Black sleeving gives a uniform look and resists abrasion during routing. The right-angle reverse connector points the cable toward the motherboard tray instead of the side panel, easing closure in tight cases. Three connectors total keep the run short and reduce clutter behind the graphics card.
How it compares
Measured against everything we stock in Internal PSU & Riser Cables, at today’s prices. Recalculated every night.
- Price $10.99
- Cheaper than about 70% of the 7,693 comparable items (median $14.99).
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Specifications
| Product | |
|---|---|
| Product color | Black |
| Ports & slots | |
| First connector | 12+4Pin Male 90 Degree Reverse |
| Second connector | 2 × 8Pin Male |
| Connector count | 3 |
| Size & build | |
| Overall length | 10CM |
Questions about this item
Will the 90-degree reverse 12+4Pin connector fit alongside my existing 8-pin cables in a tight case?
The 90-degree reverse 12+4Pin male connector bends away from the GPU, so it sits flush against the card and leaves room for adjacent 8-pin cables in compact builds.
How can I verify the cable is delivering the full 32GT/s data link after installation?
The H++ cable is rated for PCIe 5.0 at 32GT/s; confirm operation by checking GPU-Z or the driver control panel for a stable PCIe 5.0 x16 link with no fallback to lower speeds.
Does the package include the two 8-pin PSU cables or only the 12+4Pin extension?
The box contains the single 10cm sleeved extension with a 12+4Pin male connector on one end and two 8-pin male connectors on the other; PSU-side 8-pin cables are not included.
More in Internal PSU & Riser Cables
Similar items
Nippon Labs POW-04412 12" Molex 5.25 Female to Female internal power cable
- 1 ft (0.3 m)
- Multi-Color
Lian Li PW-PCI-520X PCIe 5.0 riser cable 200 mm
- PCIe 5.0 Riser Cable
- Black
Silverstone Technology PP14-PCIE 2x PCIe 8-pin to 12VHPWR internal power cable
- 2x PCIe 8pin female
- 1x 12VHPWR PCIe Gen…





