Barrow Mods TNYBT4-A02-Silver G1/4 to 1/2" Barb Fitting Silver
Connects G1/4" watercooling ports to 1/2" ID tubing for fill, drain or stop fitting use
- Product colorSilver
- Key featuresCompatible with standard G1/4 in threaded ports on most wate
- Connects G1/4" ports to 1/2" ID tubing for custom loops
- Silver finish matches common water-cooling colour schemes
- Barbed end secures tubing without extra clamps
- Works as fill, drain or stop fitting in one piece
- Standard G1/4" thread fits most blocks, radiators and reservoirs
G1/4 to 1/2" Barb Fitting for Watercooling Loops
This silver adaptor connects standard G1/4" threaded ports to 1/2" inner-diameter tubing. It suits builders assembling custom liquid-cooling circuits who need a reliable transition between component threads and soft tubing. The fitting works as a fill port, drain port or stop fitting in a loop. Buyers requiring metric-threaded ports or smaller tubing diameters cannot use this part.
Hand-Tighten Installation With Optional Clamp
Screw the G1/4" male thread into any matching female port on a reservoir, radiator or block until the O-ring seats. Push the barbed end fully into 1/2" ID tubing; a hose clamp or compression ring is recommended to prevent the tube sliding off under pressure. The most common error is leaving the barb partially inserted, which causes slow leaks once the system is pressurised. No tools are required beyond fingers and, optionally, pliers for the clamp.
Verify Port Thread and Tubing ID Before Ordering
Confirm every component you plan to connect exposes a G1/4" female thread; other thread standards will not seal. Check that your soft tubing specifies a 1/2" inner diameter — larger or smaller bore will not grip the barb correctly. Ensure you have enough clearance around each port for the fitting body and the tubing bend radius. If your loop uses hardline tubing or quick-disconnect couplings, this barb fitting is not compatible.
How it compares
Measured against everything we stock in SATA & eSATA Drive Cables, at today’s prices. Recalculated every night.
- Price $6.99
- Cheaper than about 85% of the 1,954 comparable items (median $13.99).
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Specifications
| Product | |
|---|---|
| Brand name | Barrow |
| Model name | TNYBT4-A02-Silver |
| Product color | Silver |
Questions about this item
How can I confirm the G1/4" thread is sealing properly after installing the silver barb fitting?
Tighten the G1/4" thread into the port, push 1/2"ID tubing onto the barbed end, then run the loop under pressure and check for leaks at both connections.
What comes with the TNYBT4-A02-Silver fitting and what must I supply myself?
The fitting itself is included; you must provide 1/2"ID tubing and a G1/4" threaded port on your watercooling component.
Which version of this adaptor should I choose for a standard G1/4" watercooling port and 1/2"ID tubing?
The TNYBT4-A02-Silver model matches a G1/4" thread on one side and a 1/2"ID barb on the other, so select this single version.
More in SATA & eSATA Drive Cables
Similar items
Nippon Labs SATA3L1.5FT-90/180RD 1.5 ft SATA III cable 90 to 180 degree
- 1.5 ft (0.46 m)
- SATA III
STARTECH SATA6RA1 6" SATA right-angle cable 26 AWG 152.4 mm
- 6 in (15.2 cm)
- Cable Connectors
Micro Connectors 12 Inches 15-pin SATA Male to Female Power Extension Cable
- 1 ft (0.3 m)
Nippon Labs SATA-1MR 1m right-angle SATA cable
- 3.28 ft (1m)
- SATA
Micro Connectors SATA III straight to right-angle cable 20" black 3-pack
- Black





