Cables To Go 10181 7-Pin 180° to 90° SATA cable Red 18
Connects SATA drives with 180° and 90° angled plugs to reduce cable strain and improve airflow
- Cable length0.5 ft (0.15 m)
- Connector count2
- Connector genderMale to Male
- Product typeCable Connectors
- Product colorRed
- Overall length18 in (45.7 cm)
- Angled connectors reduce cable strain for longer life
- 180° to 90° design eases routing in tight cases
- Red 18-inch cable cuts clutter and improves airflow
- Male-to-male 7-pin SATA supports up to 6 Gbps transfers
- RoHS compliant build meets environmental standards
Straight-to-angled SATA cable for tidy builds
This Cables To Go 10181 cable links a 7-pin SATA device to a motherboard or host controller using a 180° straight plug on one end and a 90° angled plug on the other. The 18-inch red cable is designed to reduce bend stress at the connector, helping the link last longer inside a chassis. It supports transfer rates up to 6 Gbps and meets RoHS requirements.
Builders routing drives in tight corners.
The right-angle connector lets the cable sit flat against a drive or motherboard header, improving airflow and cutting clutter in compact cases or crowded drive cages. The half-foot length suits adjacent ports but will not reach devices mounted far from the controller. Installers needing a straight-to-straight layout or a longer reach should choose a different cable.
One drive per cable at full 6 Gbps headroom
Each assembly carries a single device connection, so a SSD or hard drive gets the full 6 Gbps bandwidth with no sharing. The short 18-inch run keeps signal loss low, but the fixed length leaves no slack for rerouting if the drive bay moves. Multi-drive arrays will need one cable per device.
How it compares
Measured against everything we stock in SATA & eSATA Drive Cables, at today’s prices. Recalculated every night.
- Price $6.99
- Cheaper than about 85% of the 1,954 comparable items (median $13.99).
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Specifications
| Product | |
|---|---|
| Brand name | C2G |
| Model name | 10181 |
| Product type | Cable Connectors |
| Product color | Red |
| Ports & slots | |
| Connector count | 2 |
| Connector gender | Male to Male |
| Size & build | |
| Overall length | 18 in (45.7 cm) |
| Cable length | 0.5 ft (0.15 m) |
| Shipping weight | 0.02 kg |
| Package size | 102 × 57 × 13 mm |
Questions about this item
Does my motherboard or host controller need a standard 7-pin SATA port to use the C2G 10181 cable?
Yes, both connectors on this cable are 7-pin Serial ATA male plugs, so your board or controller must provide matching 7-pin SATA ports.
Will the 180° and 90° angled ends fit alongside older straight SATA cables already routed in my case?
The mixed-angle design lets one end run flat against the motherboard while the other angles away, reducing interference with existing straight cables in tight spaces.
How can I verify the cable is delivering the supported 6 Gbps transfer rate after installation?
Check the negotiated link speed in your BIOS or operating-system disk utility; it should report 6 Gbps when the drive and controller both support that rate.
More in SATA & eSATA Drive Cables
Similar items
Nippon Labs SATA3L1.5FT-90/180RD 1.5 ft SATA III cable 90 to 180 degree
- 1.5 ft (0.46 m)
- SATA III
STARTECH SATA6RA1 6" SATA right-angle cable 26 AWG 152.4 mm
- 6 in (15.2 cm)
- Cable Connectors
Micro Connectors 12 Inches 15-pin SATA Male to Female Power Extension Cable
- 1 ft (0.3 m)
Nippon Labs SATA-1MR 1m right-angle SATA cable
- 3.28 ft (1m)
- SATA
Micro Connectors SATA III straight to right-angle cable 20" black 3-pack
- Black





