Darkside Computer Modding 30cm SATA 3.0 180° to 90° Cable Graphite Metallic DS-0555
A 30 cm SATA 3.0 cable with a straight-to-right-angle connector for tight drive bays
- Cable length1 ft (0.3 m)
- SATA 3.0 support delivers 6 Gb/s transfer speeds
- 180° to 90° angled connectors ease routing in tight cases
- 30 cm length reduces cable clutter inside the build
- Graphite metallic sleeving adds a clean, mod-friendly look
- Latching connectors secure the link against vibration and movement
Cable length and connector angles
This 30 cm SATA 3.0 cable connects a straight 180° plug to a right-angle 90° plug. It is built for modders who want a coloured, sleeved data link inside a custom PC. The graphite metallic finish matches themed builds without adding bulk. Buyers who need an internal power cable or an external eSATA link should look elsewhere.
Signal integrity and airflow
The slim sleeved jacket keeps the cable flexible so it routes cleanly behind motherboards and drive cages. A secure latch on each connector prevents accidental disconnection during transport or vibration. No active cooling or power draw is involved, so the cable adds zero noise or heat to the system. It simply carries the SATA 3.0 signal between host and device.
Sustained data transfer
Under continuous read or write loads the cable maintains the full SATA 3.0 bandwidth because the conductors and shielding meet the 3.0 specification. The right-angle end reduces strain on the device port during long sessions, lowering the risk of intermittent errors. Performance does not degrade over time as there are no active components to overheat. Builders who require longer runs beyond 30 cm will need a different length.
How it compares
Measured against everything we stock in SATA & eSATA Drive Cables, at today’s prices. Recalculated every night.
- Price $2.99
- Cheaper than about 95% of the 1,954 comparable items (median $13.99).
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Specifications
| Size & build | |
|---|---|
| Cable length | 1 ft (0.3 m) |
Questions about this item
How do I install the 180° to 90° SATA cable and which connector goes where?
Plug the straight 180° end into the motherboard or controller port, then route the right-angle 90° end to the drive; the latch clicks only when fully seated, so push until you hear it engage.
What maintenance or replacement will this 30 cm SATA 3.0 cable need over time?
The sleeved jacket resists abrasion, but inspect the latch tab after any rebuild — if the clip snaps or the connector feels loose, replace the cable to avoid intermittent detection.
What limit appears first when this 1 ft cable runs sustained 6 Gbit/s transfers?
The 30 cm length keeps signal loss minimal, so the first bottleneck is usually the drive’s own sustained throughput or the controller queue depth, not the cable itself.
More in SATA & eSATA Drive Cables
Similar items
Nippon Labs SATA3L-1.5FT-RD 1.5 ft SATA III cable UV Red
- 1.5 ft (0.46 m)
- SATA III
Nippon Labs SATA-1MR 1m right-angle SATA cable
- 3.28 ft (1m)
- SATA
Darkside DS-0966 SATA M/F Extension Cable Jet Black
- Black
- Compliment your bui…
STARTECH SATA6RA1 6" SATA right-angle cable 26 AWG 152.4 mm
- 6 in (15.2 cm)
- Cable Connectors
Darkside CONNECT SATA Cable Type 16 5-Pin 30cm Black DS-1019
- 1 ft (0.3 m)





