Vszerda M.2 SATA B/B+M Key to 2.5" SATA Adapter
Converts SATA-based M.2 NGFF SSDs (B key, B+M key, 2230–2280 mm) to a 2.5" SATA 6.0 Gbps interface, but does not support PCIe NVMe M-key drives
- Converts SATA-based M.2 NGFF SSDs into 2.5" SATA 6.0 Gbps drives
- Supports B key and B+M key M.2 SSDs in 2230, 2242, 2260, 2280 lengths
- Works with SATA revision I, II, III at 1.5, 3.0, 6.0 Gbps
- Reduces power consumption using high-efficiency M.2 SSD
- Does not support PCIe M key or M+B key NVME SSDs
Vszerda M.2 SATA Adapter for 2.5" Bays
This adapter converts a SATA-based M.2 NGFF SSD into a standard 2.5-inch SATA drive form factor. It is designed for users who want to install an M.2 SATA drive into a laptop or desktop bay that only accepts 2.5-inch drives. The card supports B key and B+M key M.2 modules in lengths from 2230 to 2280 millimetres. It does not work with PCIe-based NVME drives.
Sustained SATA III throughput up to 6.0 Gbps
The adapter maintains the full SATA III interface speed of 6.0 Gbps and is backward compatible with SATA revision I and II rates of 1.5 and 3.0 Gbps. Because it is a passive electrical conversion with no controller chip, sustained transfer rates depend entirely on the installed M.2 SATA SSD's own capabilities. There is no thermal throttling or protocol overhead introduced by the adapter itself.
Simple screw-mount installation with keying caution
Mount the M.2 SSD onto the PCB using the standoff and screw, then secure the assembly into a 2.5-inch drive bay or caddy. The most common issue is attempting to install an M key or M+B key NVME drive, which is physically incompatible and electrically unsupported. Verify the SSD uses a B key or B+M key SATA interface before purchase to avoid a mismatch.
How it compares
Measured against everything we stock in SATA & eSATA Drive Cables, at today’s prices. Recalculated every night.
- Price $13.99
- Typical for this category: the median of 1,954 items is $13.99.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Specifications
No published specifications for this item yet.
Questions about this item
Does the adapter generate noticeable heat or draw extra power when an M.2 SATA SSD runs continuously?
The adapter is a passive board with no active components, so it adds no measurable heat or power draw beyond the SSD itself.
What host connector must my system provide for this adapter to work?
Your motherboard or enclosure needs a standard 2.5-inch SATA data and power connector.
Can I keep using my existing 2.5-inch SATA cables and drive bay with this adapter installed?
Yes, the adapter presents a regular 2.5-inch SATA interface, so your current cables and bay work without change.
More in SATA & eSATA Drive Cables
Similar items
DKARDU NR-US-050 4-pack 22-pin SATA combo extension cable 50cm
- Optical
- SATA
Nippon Labs SATA-1MR 1m right-angle SATA cable
- 3.28 ft (1m)
- SATA
AYECEHI SATA III 6.0 Gbps cable 90° locking latch blue 12 inch 6 pack
- Sata
- Male-to-Male
STARTECH SATA6RA1 6" SATA right-angle cable 26 AWG 152.4 mm
- 6 in (15.2 cm)
- Cable Connectors





